aliennawer.blogg.se

1. Rs ba1 version 2 download install#
2. Rs ba1 version 2 download drivers#
3. Rs ba1 version 2 download update#
4. Rs ba1 version 2 download driver#

Touch “Network User1” to open the network between the IC-705 and the RS-BA1.ĥ. Note: ADSL/CATV may be possible depends on your Wi-Fi systemĤ. Touch “▼” to go to the next page on 2/2 and make sure each item of settings is set as follows. If the set value is not the same as the one shown below, touch the item to change it.ģ. Make sure each item of settings on the REMOTE SETTINGS 1/2 is set as follows. Push to open the menu screen, then touch the following items to open the REMOTE SETTINGS screen, as shown below.Ģ. Next, you need to have to set remote settings between the IC-705 and the router through your network.ġ. Take note of the IP address for later use in the RS-BA1 settings. This is because IP address is allocated to each system by the server. Appeared IP address on your PC is different from the IP address shown below.

Touch the return icon to show the “DHCP (Valid after Restart)” confirmation screen, shown below. If the password is correct, and the connection is properly performed, the display shows “Connected.”Ĥ. Enter a password for your router with the on-screen keyboard, then, touch. Note: The ACCESS POINT screen does not display routers that use the 5 GHz band because the IC-705 does detect only Wi-Fi devices used in the 2.4 GHz band.ģ. The display shows the WLAN 1/1 screen shown. (1) Connecting between the IC-705 and the Wi-Fi routerĢ. (1) The first settings are to connect to your router, and the second settings are to set and confirm the IC-705 remote settings, as described below. Several settings and confirmations are necessary for connecting an access point, such as a Wi-Fi router. Image of the in-house remote operation with the IC-705 Connecting to a Wi-Fi router

Rs ba1 version 2 download driver#

You can download the latest IC-705 driver from the following website:Ī wireless access point, such as a Wi-Fi LAN router is required to connect the IC-705 to the Internet.

Rs ba1 version 2 download drivers#

USB drivers for Icom products other than the 705 cannot be used. You can download the latest IC-705 firmware from the following website:

Rs ba1 version 2 download update#

The IC-705 can support wireless remote operation, even if your firmware is not the latest version, but we recommend that you update if possible. The firmware IC-705 version is displayed on the right bottom side corner on the display when the power is initially turned ON. You can download the latest RS-BA1 Version 2 upgrade software from the following website: Read the RS-BA1 Version 2 instruction manual for about its installation. Make sure that the Remote Utility and the Remote Control shortcut icons appear on your PC’s desktop screen after the installation is successful. This is because notebook PCs are convenient to carry anywhere in your house. We recommend a notebook PC with the Wi-Fi function installed.

Rs ba1 version 2 download install#

Install the RS-BA1 Version 2 to your PCįirst, install the RS-BA1 Version 2 on your PC. Please note that it you must upgrade RS-BA1 Version 2 to version 2.20 or later, as the IC-705 is not supported if the software version is earlier than 2.2. Unfortunately, even if you already have the original RS-BA1 software, you need to purchase the RS-BA1 version 2. The software is an Icom product and is sold worldwide. To succeed in wireless remote operation, you need a PC as well as the RS-BA1 Version 2 remote control software. If you have Wi-Fi service at home, I would like to introduce an example where you can enjoy in-house wireless remote operation using Icom’s RS-BA1 Version 2 remote control software.įor example, you can remotely operate the IC-705 to set up your radio shack by using Wi-Fi, while you are lying on the sofa in your living room.